Review: Hellvape Dead Rabbit V2 RTA
Publicado: 23 Jun 2020, 11:24
Hi, friends. For appetizer, a copy, as always, is more interesting, and even less. The novelty appeared in the camp of old-timers - the company Hellvape, moreover, the line of the dead rabbit was supplemented. Namely, the serviced tank of the second revision was presented - Dead Rabbit V2 RTA Hellvape. There are not many changes, but they are, albeit not so dramatic.
Parameters
Case material: stainless steel
Atomizer type: RTA
Capacity: 2 / 5ml
Diameter: 25mm
Height: 50.5mm with drip tip
Connector: 510, gold-plated pin
The appearance of the new item has not changed much, since the non-spillable construct has been preserved. To differ from the first version, we changed the knurling pattern on the lid and in the base, and the lid itself began to look a bit more massive. Engraving on the dome naturally has not gone away.
The proposed palette of offers, as always with Hellvape new vape, is full of variety, and the whole gamut is available right from the moment of release. The drip tip is made of delrin, landing 810th. It differs in form from familiar specimens - a small skirt is visible at the base. But the second instance in the kit is no longer there. The next innovation is a slide cover similar to unserviceable.
A little lower is the traditional airflow adjustment ring. And here we are taken aback by the following difference - the double dome. Earlier, I recall, the dome was single. The geometry of the air flow inside the tank has not changed, except that now the mesh outlet air vents.
Summary
You should definitely remember Hellvape Dead Rabbit RTA version 2. Correctly fix the same four posts of two spirals. Just like dripping water, the difference here is that the angle of inclination of the "ear" of the rack is now greater than 90 degrees and the perforations are larger. The holes for laying cotton with restrictors, although large.
Related products we recommend:
joyetech exceed grip pro
voopoo drag x
What’s new
https://vapesourcing.com/freemax-fireluke-3-tank.html
https://vapesourcing.com/freemax-m-pro-2-tank.html
Parameters
Case material: stainless steel
Atomizer type: RTA
Capacity: 2 / 5ml
Diameter: 25mm
Height: 50.5mm with drip tip
Connector: 510, gold-plated pin
The appearance of the new item has not changed much, since the non-spillable construct has been preserved. To differ from the first version, we changed the knurling pattern on the lid and in the base, and the lid itself began to look a bit more massive. Engraving on the dome naturally has not gone away.
The proposed palette of offers, as always with Hellvape new vape, is full of variety, and the whole gamut is available right from the moment of release. The drip tip is made of delrin, landing 810th. It differs in form from familiar specimens - a small skirt is visible at the base. But the second instance in the kit is no longer there. The next innovation is a slide cover similar to unserviceable.
A little lower is the traditional airflow adjustment ring. And here we are taken aback by the following difference - the double dome. Earlier, I recall, the dome was single. The geometry of the air flow inside the tank has not changed, except that now the mesh outlet air vents.
Summary
You should definitely remember Hellvape Dead Rabbit RTA version 2. Correctly fix the same four posts of two spirals. Just like dripping water, the difference here is that the angle of inclination of the "ear" of the rack is now greater than 90 degrees and the perforations are larger. The holes for laying cotton with restrictors, although large.
Related products we recommend:
joyetech exceed grip pro
voopoo drag x
What’s new
https://vapesourcing.com/freemax-fireluke-3-tank.html
https://vapesourcing.com/freemax-m-pro-2-tank.html